A leaking or fogged skylight is one of the more anxious roofing problems for an island homeowner, because it sits at the intersection of two systems: the glass unit itself and the roof it penetrates. On the San Juan Islands, with roughly 40 inches of annual rain, wind-driven storms, and salt air working on every metal component, a skylight problem rarely stays small if it is ignored. The core question is always the same. Do you repair the skylight you have, or replace it entirely? This comparison lays out how to decide. What Actually Fails on a Skylight Understanding the failure points makes the repair-versus-replace call much clearer. Flashing and seal. The most common leak source is not the glass but the flashing and sealant where the skylight meets the roof. Wind-driven island rain finds any gap. Seal failure (fogging). When the seal between insulated glass panes fails, moisture gets trapped and the unit fogs permanently. That is a unit problem, not a flashing problem. Cracked glass or dome. Impact, hail, or a fallen branch can crack the pane. Aged framing and gaskets. Older units develop brittle gaskets and corroded frames, especially near saltwater. Condensation confusion. Sometimes what looks like a leak is interior condensation from poor ventilation, not a roof failure at all. The Head-to-Head Comparison The table below frames the decision across the factors that matter most on an island roof. Factor Repair Replacement Best when Flashing/seal leak, minor gasket issue, unit under ~10 years Fogged seal, cracked glass, unit 15+ years, repeated leaks Typical cost range $450–$1,500 $1,200–$3,500+ Disruption Low; often a half-day Higher; roof opening reworked Longevity gained A few years if unit is aging 20+ years with a modern unit Energy performance Unchanged Improved (modern glazing) Risk of recurrence Higher on old units Low Roof integration Reuses existing curb/opening Fresh flashing and membrane Costs shown are an estimate, not a quote. On the islands, expect roughly 10 to 25 percent above comparable mainland pricing because crews and materials cross by ferry and old units leave the same way. When Repair Is the Right Call Repair makes sense when the skylight unit itself is sound and the failure is at the connection to the roof. Good Repair Scenarios The leak traces to failed flashing or dried sealant, and the glass is intact and clear. The unit is relatively young, generally under about ten years. A single gasket or a cracked exterior dome can be replaced without disturbing the whole assembly. The key to a lasting island repair is doing the flashing right. That means corrosion-resistant metal, fresh sealant rated for the exposure, and ice-and-water membrane integrated at the skylight where wind-driven rain concentrates. A sealant-only smear over old flashing is a stopgap that will fail again by the next November. When Replacement Wins Replacement is the honest answer more often than homeowners expect, because patching an aging unit often just delays a second bill. Clear Replacement Signals Persistent fogging between panes. A failed insulated seal cannot be repaired; the unit must be replaced. Cracked glass. Structural glass damage means a new unit. Repeated leaks. If a skylight has leaked, been patched, and leaked again, the assembly is telling you something. Age. Units past 15 to 20 years are near end of life; reworking the flashing on an old, inefficient unit rarely pays off. Roof replacement timing. If you are re-roofing anyway, replace skylights at the same time. Opening the roof twice on an island, with ferry-driven labor costs, is money wasted. A modern replacement also upgrades energy performance. Older single- or early double-pane units bleed heat; today's low-emissivity glazing cuts that loss and reduces the condensation that gets mistaken for leaks. The Island-Specific Factors Several local realities should weigh on the decision. Salt air. Near saltwater, corroded frames and fasteners argue for replacement with corrosion-resistant components rather than nursing old hardware along. Access and staging. Ferry logistics make every visit more expensive, so consolidating work, replacing rather than making a second repair trip, often costs less over time. Moss and shade. Skylights on north slopes under Douglas fir collect debris and moss around the curb, which traps water. Whatever you choose, keep the surrounding roof clear. Wind. West-side exposures drive rain uphill and sideways, stressing flashing hard. That environment rewards a properly integrated new curb and flashing over an old, marginal seal. How to Decide, Step by Step Homeowners weighing options for https://charliexlcs019.readspirex.com/posts/how-to-clean-your-roof-without-damaging-it can work through a simple sequence: Confirm the source. Is it flashing, a fogged seal, cracked glass, or interior condensation? The fix depends entirely on this. Check the age. Under ten years and structurally sound leans repair. Fifteen-plus leans replace. Count the leaks. First leak on a young unit: repair. Repeat offender: replace. Consider timing. Re-roofing soon? Replace the skylight in the same project. Account for salt and access. Corrosion and ferry costs both tilt the math toward doing it once, correctly. The Bottom Line Repair a young, sound skylight with a flashing or seal problem, and insist on corrosion-resistant flashing done to island standards. Replace a fogged, cracked, or aging unit, and always replace skylights during a re-roof rather than reopening the roof later. On the islands, where weather is relentless and every trip across the water carries a premium, the durable choice usually beats the cheap one within a few seasons. About the Author Nora Whitfield is a home-improvement writer and former glazing technician who has worked on daylighting and roof penetrations throughout the maritime Pacific Northwest. She focuses on helping homeowners make weather-smart repair-or-replace decisions.
10 Roofing Materials Ranked for Salt-Air Durability
Living on the San Juan Islands means living with salt. It drifts off the water on every breeze, settles on every surface, and quietly attacks anything that cannot resist it. Cheap fasteners rust, thin coatings chalk and peel, and porous materials trap the moisture that our roughly 40 inches of annual rain deliver. When you factor in west-side wind gusts about 20 percent stronger than Anacortes and moss creeping across shaded north slopes, the question of which roofing material to choose becomes less about looks and more about survival. This is a ranking of ten common roofing materials by how well they hold up to salt air on the islands. Every material can be made to work with the right details, but some fight the climate and some cooperate with it. How the Ranking Works Salt-air durability comes down to three things: how the material itself resists corrosion and moisture, how its fasteners and coatings hold up, and how easily moss and water can gain a foothold. A material that scores well on all three ages gracefully here. One that fails on even one becomes a maintenance burden. Rank Material Salt-Air Durability Est. Lifespan (islands) Notes 1 Standing-seam metal (24-ga Kynar 500) Excellent 50+ years Hidden fasteners, marine coating, sheds moss 2 Aluminum roofing Excellent 40–50 years Naturally corrosion-resistant, ideal near water 3 Copper Excellent 60+ years Premium cost, patinas beautifully, slows moss 4 Concrete tile Very good 40–50 years Heavy, needs strong framing 5 Synthetic composite Very good 30–50 years Mimics slate or shake, lightweight 6 Architectural asphalt Fair 20–30 years Common and affordable, weak on shaded slopes 7 TPO / PVC membrane (flat) Good 20–30 years For low-slope; seams need quality installation 8 EPDM membrane (flat) Fair 15–25 years Economical flat option, less UV-stable 9 Exposed-fastener metal Fair 25–40 years Metal lasts; the screws are the weak point 10 Cedar shake Demanding 20–30 years with upkeep Beautiful but high-maintenance in wet salt air The Standouts 1. Standing-Seam Metal For island homes, this is the benchmark. Panels run in continuous lengths with concealed fasteners, so there are no exposed screws to corrode. Specified in 24-gauge steel with a marine-grade Kynar 500 (PVDF) coating and corrosion-resistant fasteners, it can last more than 50 years against salt, wind, and rain. Its smooth surface gives moss almost nothing to grip, and a zinc or copper ridge strip discourages what little tries to grow. 2 and 3. Aluminum and Copper Both are metals that shrug off salt by nature. Aluminum does not rust, which makes it a natural fit for homes right on the shoreline. Copper is the aristocrat of the group, lasting well over half a century and developing a protective patina that also slows moss. The barrier for both is cost, but their longevity can justify the investment on an exposed waterfront property. The Solid Middle 4 and 5. Concrete Tile and Synthetic Composite Concrete tile resists salt and fire well and lasts for decades, though its weight demands robust framing that not every island home has. Synthetic composites, engineered to mimic slate or cedar shake, deliver strong durability at a fraction of the weight and much less maintenance than the real thing. Both are worth a look if metal is not your aesthetic. 6 and 7. Asphalt and Flat Membranes Architectural asphalt is the workhorse: affordable, widely available, and good for 20 to 30 years, though it struggles on the shaded, moss-prone north slopes under our firs. For the flat and low-slope sections common on modern island homes, TPO and PVC membranes perform well when the seams are welded properly. If you are comparing bids and researching https://ricardonoam667.scriblorax.com/posts/gutters-vs.-gutter-guards-what-island-homes-need , pay close attention to who is installing these membranes, because a flat roof lives or dies by seam quality. The Cautions 8 and 9. EPDM and Exposed-Fastener Metal EPDM is an economical flat-roof rubber, but it is less UV-stable and tends to need attention sooner. Exposed-fastener metal is a tempting budget version of standing seam, and the metal itself lasts, but every screw is a penetration with a rubber washer that eventually fails. In salt air those fasteners are the first thing to go. 10. Cedar Shake Cedar is genuinely beautiful and historically at home in the Northwest, but it is the most demanding option on this list. In our wet, salty, moss-friendly climate it requires constant cleaning, treatment, and vigilance to reach the top of its lifespan. Choose it with your eyes open to the upkeep. A Note on Cost and Logistics Rough installed-price estimates on the islands run from about $9k to $24k for asphalt, $14k to $45k-plus for standing-seam metal, and $8k to $26k for flat systems. Ferry logistics for crew, materials, and off-island disposal typically add roughly 10 to 25 percent over a comparable mainland job. These are ballpark ranges, not quotes; complexity, gauge, and coating all move the number. The takeaway is simple. Near saltwater, spend your money on corrosion resistance: the right metal, the right coating, and the right fasteners. That is what separates a roof that lasts a lifetime from one that becomes an annual chore. About the Author Priya Anand is a coastal materials writer who has spent years comparing how building products age in the salt and rain of the Pacific Northwest. She believes the smartest roofing decision is usually the one that never asks for your attention again.
If you have decided on an asphalt roof for your San Juan Islands home, you still face one more fork in the road: architectural shingles or 3-tab. They come from the same family, sit in the same aisle, and both are asphalt, yet they perform very differently through a wet, windy island winter. This comparison lays out how the two stack up on look, lifespan, wind resistance, moss behavior, and cost, so you can spend your roofing budget where it actually counts. The Basic Difference 3-tab shingles are a single, flat layer cut into three uniform tabs. Every shingle looks identical, giving a clean but noticeably flat, repetitive appearance. They are the lightweight, economical original. Architectural shingles, also called dimensional or laminated shingles, are built from two or more layers bonded together. That extra layer adds thickness, a varied shadow-line texture that mimics wood shakes, and considerably more durability. They are heavier, thicker, and stronger. That structural difference, one layer versus laminated layers, is the reason architectural shingles cost more and last longer. Head-to-Head Comparison Factor 3-Tab Architectural Construction Single flat layer Two-plus laminated layers Typical lifespan 15–20 years 25–30 years Wind rating Lower (often ~60 mph) Higher (often 110–130 mph) Appearance Flat, uniform Dimensional, shake-like Weight Lighter Heavier, more robust Moss resistance Poor Slightly better, still needs help Warranty Shorter Longer Relative cost Lowest asphalt option Higher, still mid-range overall Why the Islands Tip the Scales In a mild, dry climate the two shingles are closer competitors. Island conditions widen the gap. Wind The west sides of the islands see wind roughly 20 percent stronger than nearby Anacortes. 3-tab shingles rely on a single sealant strip and lift more easily; their wind ratings are modest. Architectural shingles carry much higher wind ratings and their heavier, laminated bodies resist peeling and blow-off. In an exposed or west-facing location, that difference alone can justify the upgrade. Rain and Longevity With about 40 inches of rain a year, heaviest in November, an island roof works hard and dries slowly. The thicker architectural shingle simply has more material to give before it wears through, which is why it typically outlasts 3-tab by a decade or more. Over the life of the home, buying one architectural roof instead of two 3-tab roofs often costs less, especially once ferry logistics enter the picture. Moss Neither shingle is moss-proof. On shaded north slopes under Douglas fir, moss will try to colonize any asphalt. Architectural shingles resist it marginally better thanks to their thickness, but both benefit enormously from zinc or copper ridge strips, which release trace metals that suppress moss every time it rains. Ventilation and tree trimming matter more than the shingle choice here. The Cost Picture A typical asphalt roof on the islands runs roughly $9,000 to $24,000, with 3-tab at the lower end and architectural higher within that band. These are ranges and an estimate, not a quote; your slope, roof size, tear-off needs, and deck condition all move the number. Ferry logistics add roughly 10 to 25 percent over a comparable mainland job, because crews and material must be staged and old roofing hauled off-island for disposal. That surcharge applies every time you re-roof, which quietly rewards the longer-lasting option. Scenario 3-Tab Architectural Upfront cost Lowest Moderate Cost per year of service Higher Lower Re-roofs in 40 years About 2 About 1–2 Ferry surcharge exposure More often Less often When 3-Tab Still Makes Sense 3-tab is not obsolete. It can be the right call when: You are roofing a low-stakes structure like a shed or detached garage. You plan to sell soon and need a clean, budget-minded roof. The slope is well-protected from wind and gets good sun to dry quickly. Budget is the hard, non-negotiable constraint today. For a primary residence you intend to keep, though, the durability math usually favors architectural. When Architectural Wins Choose architectural shingles when: The roof faces west or sits in an exposed, windy spot. You want a dimensional, upscale look closer to cedar shake. You are staying in the home long term and want fewer re-roofs. You want the longer manufacturer warranty and higher wind rating. Anyone comparing bids for https://andyhbea872.talesignal.com/posts/flat-roof-systems-compared-tpo-vs.-epdm-vs.-torch-down should confirm both quotes list the shingle line, wind rating, and warranty in writing, because "asphalt shingles" on a proposal could mean either product at very different value. Getting the Most From Either Choice Whichever shingle you pick, the same island best practices protect your investment: Install ice-and-water membrane at valleys and eaves where water concentrates. Ensure balanced attic ventilation so the deck dries between rains. Add zinc or copper ridge strips on shaded, moss-prone slopes. Trim overhanging branches to reduce shade, debris, and moisture. Schedule gentle moss treatment before growth mats up; budget roughly $400 to $1,600 depending on roof size and severity. These details often matter more to real-world lifespan than the shingle grade itself. The Bottom Line 3-tab and architectural shingles share a material but not a destiny. 3-tab wins on upfront price and suits sheds, quick sales, and sheltered slopes. Architectural shingles cost more but bring a decade-plus of extra life, far better wind resistance, a richer look, and a stronger warranty, advantages that compound in a wet, windy, ferry-served island setting. For most island homeowners planning to stay put, architectural shingles are the more economical choice once you count the years, not just the invoice. Pair whichever you choose with proper ventilation, valley membrane, and moss control, and your asphalt roof will earn every season it stands. About the Author Trevor Nilsson is a residential roofing writer in the Salish Sea region who has spent years comparing shingle performance on exposed coastal slopes. He is a firm believer that the cheapest roof and the least expensive roof are rarely the same thing.
It is the question every island homeowner faces eventually: patch the roof one more time, or bite the bullet and replace it? Get it wrong in either direction and you lose money — pouring cash into a roof that is beyond saving, or tearing off one that had a decade left. This guide gives you a clear framework for deciding, calibrated to the specific realities of roofing in the San Juan Islands. Start With Three Questions Before you look at a single estimate, answer these. They resolve most cases on their own. 1. How old is the roof? Age is the strongest single signal. Asphalt shingles on an island typically last 15 to 25 years, less if moss has been neglected. Standing-seam metal can run 50 years or more. If your asphalt roof is past 20 and giving you trouble, you are usually replacing. If it is 8 years old with one leak, you are almost certainly repairing. 2. How widespread is the damage? A single leak at a flashing detail is a repair. Water showing up in several places, sagging areas, or daylight through the deck point to systemic failure. Localized problems get fixed; widespread ones get replaced. 3. What condition is the deck in? If the wood decking beneath the roofing is rotted or soft — a real risk after years of moss holding moisture on shaded north slopes — patching the surface solves nothing. Deck rot almost always tips the decision toward replacement. The Decision Table Use this to place your situation. Ranges are an estimate, not a quote, and reflect island pricing including ferry logistics — crew and material staging plus off-island disposal — which add roughly 10 to 25 percent over a comparable mainland job. Situation Repair Replace Estimated Cost One isolated leak, roof under 15 yrs ✔ $450 – $3,500 Moss present, no deck damage yet ✔ (treat) $400 – $1,600 Multiple leaks, roof 20+ yrs ✔ $11,000 – $40,000+ Rotted or sagging deck ✔ $11,000 – $40,000+ Failing flashing, sound roof ✔ $450 – $3,500 Frequent repairs, rising cost ✔ Asphalt $9k–$24k / Metal $14k–$45k+ Flat section, aging membrane ✔ or ✔ $8,000 – $26,000 When Repair Is the Right Call Repair wins when the roof is fundamentally sound and the problem is contained. Classic repair situations on island homes include: A leak traced to worn flashing around a chimney, skylight, or vent. Wind damage on the west side that lifted or tore a small area — island wind runs roughly 20 percent stronger than Anacortes, so localized wind damage is common. A cracked valley or a few displaced shingles. Moss that has taken hold but not yet rotted the deck. In these cases a targeted repair, plus preventive steps like ice-and-water membrane at the fixed valley and zinc or copper ridge strips to slow moss, buys you years at a fraction of replacement cost. When Replacement Is the Right Call Replacement wins when repairs are chasing a losing battle. Signs it is time: The roof is at or past its expected lifespan. You are repairing the same roof year after year, and the costs are climbing. Leaks appear in multiple, unrelated locations. The deck is soft, sagging, or rotted. Granules are washing into the gutters in quantity, or shingles are curling across whole slopes. Think in cost-per-year, not sticker price A $2,500 repair that buys two years costs you $1,250 a year. A $28,000 standing-seam metal roof that lasts 50 years costs $560 a year — and it is the best long-term island roof, resisting salt air, wind, and moss when built right. When you find yourself repeatedly repairing an old roof, the "cheaper" repair is often the more expensive choice over time. Island-Specific Factors That Tip the Balance A few things weigh more heavily here than on the mainland: Salt air. Near saltwater, corrosion attacks cheap fasteners and coatings. If a repair means matching an aging, already-corroding system, replacement with 24-gauge marine-grade metal and PVDF (Kynar 500) coating may make more sense sooner. Ferry logistics. Mobilizing a crew and staging materials on-island carries fixed costs. If you are going to pay to get a crew out for major work anyway, doing the job once and completely often beats repeated trips. Moss and rain. With 40 inches of rain a year and heavy November downpours, a marginal roof degrades fast. Deferring replacement on a failing roof risks deck rot that raises the eventual cost. Homeowners weighing these factors and searching for guidance on https://cashykdf177.wordpress.com/2026/07/27/how-roof-pitch-affects-material-choice-and-cost/ should get a professional inspection before deciding — the deck condition in particular is hard to judge from the ground, and it frequently settles the question. A Simple Rule of Thumb If your roof is young and the damage is localized, repair. If your roof is old and the damage is widespread — or the deck is compromised — replace. When you are genuinely on the fence, weigh cost-per-year and the island's harsh conditions, both of which tend to favor doing the job right rather than patching indefinitely. The Bottom Line There is no universal answer, but there is a reliable method: assess age, extent of damage, and deck condition; place yourself on the decision table; then think in cost-per-year rather than sticker shock. Do that honestly, factor in salt, wind, moss, and ferry logistics, and you will spend your roofing dollars where they actually protect your home. About the Author Nathan Prewitt is a Salish Sea building inspector who has evaluated hundreds of roofs on the question of repair versus replacement. He specializes in helping island homeowners read the true condition of an aging roof before they commit to a decision.